НОВЫЙ ГОСТ Р 72616–2026: ЦИФРОВИЗАЦИЯ, СТАТИСТИЧЕСКИЕ МЕТОДЫ И РИСК-ОРИЕНТИРОВАННЫЙ ПОДХОД В СФЕРЕ ТЕХНИЧЕСКОГО КОНТРОЛЯ
🇷🇺 На русском
Для цитирования
Будкин Ю.В. Новый ГОСТ Р 72616–2026: цифровизация, статистические методы и риск-ориентированный подход в сфере технического контроля // Информационно-экономические аспекты стандартизации и технического регулирования. 2026. № 5 (92). С. 4–13.
Аннотация
В опубликованной в журнале «Стандарты и качество» [1] статье представлены результаты обсуждения проекта национального стандарта, подготовленного рабочей группой Всероссийской организации качества, Института стандартизации. Документ регламентирует основные положения и порядок проведения технического контроля как составной части производственного процесса и фундамента технологической дисциплины [2–3]. После тщательного анализа предложений и замечаний в ходе дискуссии уточнены название стандарта и содержание его разделов. Показаны пути внедрения стандарта на действующих и вновь созданных предприятиях, в т. ч. малых и средних.
В связи с введением в действие 1 июля 2026 г. изменений и дополнений ГОСТ Р 72616–2026 утвержден приказом Федерального агентства по техническому регулированию и метрологии от 16 апреля 2026 г. № 375-ст. Раскроем некоторые аспекты применения стандарта для устранения недостатков в работе системы технического контроля на предприятиях.
Ключевые слова
производственный контроль
технический контроль
предприятие
входной контроль
операционный контроль
выборочный контроль
система менеджмента качества
процесс
порядок
отдел технического контроля
приемка продукции
Об авторах
Будкин Юрий Валерьевич
Список литературы
- 1. Белобрагин В.Я., Будкин Ю.В., Зворыкина Т.И. Фундамент технологической дисциплины. Новый ГОСТ Р 72616–2026 // Стандарты и качество. 2026. № 5. С. 20–24. DOI: 10.35400/0038-9692-2026-5-60-26.
- 2. Белобрагин В.Я., Зворыкина Т.И. Национальный стандарт по техническому контролю. Повышение качества производства // Стандарты и качество. 2025. № 4. С. 32–36.
- 3. Белобрагин В.Я. Поможет контролер. Соревнование и качество // Стандарты и качество. 2022. № 9. С. 48–49.
🇬🇧 In English
NEW GOST R 72616–2026: DIGITALIZATION, STATISTICAL METHODS AND RISK-BASED APPROACH IN TECHNICAL CONTROL
For citation
Budkin Y. V. New Gost R 72616–2026: Digitalization, Statistical Methods and Risk-Based Approach in Technical Control // Information and Economic aspects of Standardization and technical regulation. 2026. No. 5(92), pp. 4–13. (In Russ).
Abstract
The journal «Standards and Quality» [1] published an article reporting on the results of the discussion of the draft national standard developed by the working group of the All-Russian Organization for Quality and the Institute of Standardization. It was noted that the document regulates the basic provisions and procedure for conducting technical control as an integral part of the production process and the foundation of technological discipline [2–3]. Following a thorough analysis of proposals and comments during the discussion, the title of the standard and the content of its sections were refined. Possible ways of implementing the standard both at existing enterprises and at newly established ones, including small and medium-sized businesses, are shown. In connection with the entry into force on July 1, 2026 of amendments and additions to GOST R 72616–2026, approved by Order No. 375- st of the Federal Agency for Technical Regulation and Metrology dated April 16, 2026, it is advisable to disclose some aspects of the application of the standard to eliminate shortcomings in the operation of the technical control system at enterprises.
Keywords
production control
technical control
enterprise
incoming inspection
in-process control
sampling inspection
quality management system
process
procedure
technical control department
Т product acceptance
About the authors
References
- 1. Belobragin, V.Ya., Budkin Yu.V., Zvorykina T.I. Foundation for a technological discipline. New GOST R 72616 2026. Standarty i kachestvo [Standards and Quality], 2026, no. 5, pp. 20–24 (in Russian). DOI: 10.35400/0038 9692-2026-5-60-26.
- 2. Belobragin, V.Ya., Zvorykina T.I. National standard for technical control: improving production quality. Standarty i kachestvo [Standards and Quality], 2025, no. 4, рр. 32–36 (in Russian).
- 3. Belobragin, V.Ya. The controller will help. Competition and quality. Standarty i kachestvo [Standards and Quality], 2022, no. 9, pp. 48–49 (in Russian).